chip circuit造句
例句與造句
- It mainly contains chip circuit and the periphery circuit of it , power circuit , speech input circuit , speech output circuit , debugging circuit and rs232 circuit
包括:芯片及其外圍電路、電源電路、語音輸入電路、音頻輸出電路、系統調試電路、串口通訊電路等。 - Based on the charge pump principle analysis and circuit design in the beginning chapters , the author simulated all the sub block circuits and whole chip circuit by applying eda tools hspice and viewlogic
在完成電路原理分析與電路設計的基礎之上,還應用eda軟件hspice對各個子電路模塊和整體電路進行了功能仿真及量化模擬。 - Based on that , the author simulated most of the sub - block circuits and whole chip circuit by applying eda tools hspice . the simulation results indicate that the ic has achieved the expectation ,
理論分析、仿真結果和芯片測試數據表明,在典型情況下,該電路的電流控制精度相對誤差和匹配相對誤差可以控制在0 . 5 %以內,達到了預定設計目標。 - The author pays more attention to the analysis and design on the following sub - circuits : oscillator , comparator , hysteresis comparator , chip enable , etc . on completing the principle analysis and circuit design , the sub - circuits and whole chip circuit are verified with the eda tools hspice
其次在電路設計中,作者基于升壓型dc / dc變換器和離散脈沖頻率調制方式的基本原理并根據電路功能的需要,進行了控制電路的總體結構設計和子電路模塊設計。 - Consequently , an integrate switch mode power supply with high efficiency and good reliability can be realized by the controller with very few external parts . the fundamental principle of monolithic voltage - mode switching regulator is firstly introduced in this thesis , which is followed by a comparison between voltage - mode and current - mode converters where the pros and cons of both converters are discussed in detail ; next , the global system architecture is proposed upon the design requirements and sub - block circuits are also introduced that focuses on several essential sub - blocks such as amp , wave , pwm control , psc , osc and vref . finally , all sub - circuits and the whole chip circuit are simulated by hspice whose results indicate that the circuit function and performance have perfectly satisfied the design requirements
在論文中,首先闡述了電壓控制模式pwm開關電源的基本原理,對比了電流控制模式和電壓控制模式,分析了各自的優缺點;隨后根據設計要求進行了電路的總體設計,完成了各個子電路的原理分析,電路設計和仿真驗證,重點闡述了誤差放大電路、三角波發生電路、 pwm控制電路、節能控制電路、振蕩電路和基準源電路的分析、設計和驗證過程;最后,利用eda軟件hspice對整體電路進行了功能仿真驗證,仿真結果表明,本文完成了設計工作,達到設計要求。 - It's difficult to find chip circuit in a sentence. 用chip circuit造句挺難的
- Base on the boost principle analysis and circuit design in the beginning , the author simulated the sub - block circuits and whole chip circuit by applying eda tools hspice , the simulation result indicates that the ic has achieved the expectation of the function target and the electrical characteristics . although there were unavoidable disadvantages of this project , it is a worthwhile and valuable experience
在完成電路原理分析與電路設計的基礎之上,作者應用eda軟件hspice對各個子電路模塊和整體電路進行了功能仿真及量化模擬,仿真結果均達到或優于預定指標,驗證了作者在第二章中闡述的直流升壓boost電路的設計理論,是設計理論與實踐相結合的一次有價值的嘗試。